Friday, December 28, 2012

How to calibrate a variable speed pool pump in Arizona


Congratulations on choosing a variable speed pool pump over a single speed pump. Single speed pool pumps have been outlawed in several states and Arizona will follow in 2014 and for good reason too. Variable speed pool pumps are proven to use 80% less energy, are quieter, last longer and leave you with a cleaner pool than its single speed counter part.

Variable speed pool pumps slow down the RPMs of the pump motor to have you hundreds of dollars a year, it's comparable to driving a Pruis compared to a dragster to the grocery store. The magnetic drive is super quite and your pool is actually left cleaner because the water spends more time circulating and more time passing over the pool filter.

To fully realize the potential of your variable speed pool pump you will want it properly calibrated. A variable speed pool pump left uncalibrated can end up costing you more money if left unchecked.

Their are several items that go into a pool pump calibration including:

1. Pool volume
2. Type of filter and cleaning system
3. Static pressure of the suction and discharge lines
4. Hours of operation
5. Amperage and watts used of the variable speed pool pump

Both APS and SRP follow the National Sanitation Organization guidelines for pool pumps, stating that for a clean pool, the pump needs to turn the pool over completely once a day. If the pump turns your pool over more than once per day on a regular basis, it is overkill and wasting energy. If we have a dust storm of course you should run the pump more but not everyday.

Fortunately for you, you don't need to invest $500 in the equipment for calibration, there is a simple chart and guidelines you can use to get your variable speed pump started. Keep in mind, Green ID offers a free variable speed pool pump calibration for APS and SRP customers in the Phoenix area. All you have to do is contact us on the web @ http://www.greenintegrateddesign.com, leave your name and phone number in the contact form  and include the make and year of your variable speed pool pump. 

Sunday, December 23, 2012

Effective garage ventilation duct design in the Phoenix area

Want to convert your garage into living space or just cool down your garage during the hot summer months? Here is a list of what you need to know to make your garage a conditioned space.

1. Cover your walls and/ or garage door panels with a radiant barrier bubble wrap product, foam board or insulation. A radiant barrier bubble wrap is an effective and easy product to install. It can be bought online and will reflect radiant heat back out to the outside. It will help lower the temperature in your garage from a couple degrees to ten degrees depending on the orientation of the garage door panels.

2. Check the size of your AC system. A rule of thumb is 400 sq ft of cooling per ton, so if you have a 5 ton AC system, you have the cooling capacity for a 2000 sq ft home. Now the rule can vary greatly depending on how energy efficient your house is, including duct leakage, insulation installation and level, heat gain and room pressures. The cooling capacity is also dependent on the ductwork design and layout. A poor layout and design can greatly undercut the systems cooling capacity.

3. Add more insulation to the garage attic, go for at least 10" of cellulose insulation or 14" of fiberglass insulation.

4. Decide on how best to cool your garage, you have a few options here.

4.1 Put in new ductwork tapped into the existing ductwork. You will need to decide or consult with home performance contractor where to tap into the existing ductwork and what size line you need. A two car garage is usually 20x30 ft or a 600 sq ft area. This is the size of a master bedroom area so you will quite a bit of airflow to adequately cool the garage. Your garage may never cool enough to the inside of your home. We always go with a duct with a slightly oversized scoop and a dampener with a larger duct reducing a step down for the actual delivery of the air.

4.2 a ductless mini split AC system. This is another viable alternative that is more of a sure thing to cool your garage without taking air away from your home. The cooling capacity not be enough in our experience even if you insulate the walls in our experience. A mini split with new ducts has been successful in a converted garage to a man cave movie room we did the ductwork and insulation on.

4.3 An evaporative cooler or swamp cooler in the wall with no ductwork. This is a great option that is perfect for 2-3 months out of the year. Evap cooling during the summer months will be impossible so it may not be what you are looking for.

4.4 A window AC unit installed. You may need a larger unit unit and even then it will be hard to adequately cool the garage space.