APS Rebate Changes Summary

Home energy saving tips with a water heater timer

Lower your energy bills with a water heater timer. APS utility rates double during peak hours in the summer. SRP energy rates almost double during peak summer hours. This water heater timer shown by energy auditor David Byrnes of Green ID can turn off during peak hours, saving valuable kWhs. In Phoenix, it's impossible to get cold water during the summer anyways so why waste energy with your water heater. Save money and live happy with Green ID.

How To Perform A Variable Speed Pool Pump Calibration & Save Money On Your Energy Bills

As energy auditors and home performance contractors we often find variable speed pool pumps that have never had a proper calibration. Although we do install Hayward and Pentair variable speed pumps because of the great energy savings realized, a post-install calibration can be performed DIY. Here are some easy steps to follow to save money on your energy bills and get the most out of your variable speed pool pump.

Air Leakage Around Recessed Canned Lights

If you have had an APS energy audit or SRP energy audit performed on your home the auditor probably showed you the blower door readings or thermal images of your canned lights.  These are notoriously leaky and if a smoke pen is held up to the light, you can see the smoke gets easily sucked right up into the attic through recessed light.  If your home has more than 10 of these recessed lights, it can be a significant source of air leakage in your home.  The average home wastes about $5 to $30 per year per recessed light so it is an important cost savings consideration and health and safety concern if moisture escapes into the attic as well. Here is a little background on these lights and what you can do to stop excess air leakage in your home.

Recessed lights are typically installed in areas of high traffic areas like kitchens, hallways and family rooms.  Canned lights are either IC rated, insulation contact rated, or non IC rated, which cannot come into contact with insulation.  If additional insulation has ever been added to your home you may want to check that the insulation contractors put some sort of protector around the light before blowing more in.   Typically in homes built before 1995, non IC canned lights were used but I have seen plenty of newer homes with non IC rated canned lights installed.  You can find out if your lights are IC rated by going in the attic and looking at the nameplate of the metal light.  There is usually a label glued on top of the light that says the specifications of the light and it will say, “IC Rated”. 

Recessed lights in a two story home can also contribute to the stack effect if there are enough lights in the ceiling.  The stack effect is when warm air rises and is replaced by cool air entering the home through outside penetrations and duct leakage.  The stack effect and air leakage can be stopped by air sealing the home including the canned lights.  To find more information on how canned lights can contribute to the stack effect in your home check out this article by the Pennsylvania Housing Research Center.

There are several ways you can effectively seal your canned lights by either replacement or retrofit.  Replacement options can be done with air tight LED lights or air tight recessed canned lights.  Both replacements are very effective, the advantages of LEDs are a longer lifespan, are fully dimmable, and use less energy.  Replacements done with air tight recessed lights are also very good.  I recently performed an energy audit on a home built in 2006 that had the new air tight recessed lights and can verify that the leakage of the light is very low.  The reading from the canned light you see on my manometer is 0.9 Pa and a typical canned light measures at 40 Pa, which is a lot of leakage.

The other option is to build energy lids with at least 3-inches of clearance between the light and the box.  The energy lid can be fitted over the canned light and sealed at its edges.  Warning!  Do not use expanding foam to seal a canned light; the foam can drip down into the house and on the trim.  The energy lids can be effective if you have non IC rated recessed lights and need to add more insulation to your attic.  You can view more tips on how reduce your energy bills here.

For a guide on ways to seal up your home check out EnergyStar’s publication on air leakage and air sealing your home.

Why Are There Radiant Barrier a Scam Claims?

So you are doing your due diligence by researching whether or not radiant barrier is a scam is true.  Radiant barriers installed in existing homes have generated a lot of confusion and controversy.  Often energy saving claims have become grossly bloated from 20% of air conditioning bills to 20% of your entire electricity bill, which is quite different.  Consider this, if heat gain into a home with good insulation is only 15%, how can a radiant barrier reduce the energy bill by a minimum of 25%?  It’s impossible!

A homeowner today should also be aware that there is no one energy saving upgrade that will create a high performing home in terms of comfort, lower air conditioning bills and air quality.  Homeowners should therefore be considerate of alternative recommendations such as duct sealing and air conditioning tune-ups to work in conjunction with a radiant barrier.  The Department of Energy has performed studies and written articles on radiant barrier foil and has concluded it works by reducing attic temperatures and thus reduces heat gain into a home.  What is the problem then?  We will cover that later but first I’d like to go over the different types of radiant barriers on the market.  

Radiant barrier paint, radiant barrier chips and radiant barrier foil are the three types of radiant barriers.  We do not support the installation of radiant barrier chips or radiant barrier paint.  Radiant barrier paint can be diluted in the field with water and will lose its effectiveness when applied.  I’ve seen many houses where the radiant paint looks more like gray paint rather than a reflective paint, which is a sign of dilution.  Radiant barrier paints also has lower performance standards with higher emittance values and lower reflectance values than traditional radiant barrier foils.  Radiant barrier chips are not recommended because installers usually do not install them with enough density to cover the entire surface area of the attic and they can be easily moved.  Besides the radiant barrier paint and chips, we do support the use of radiant barrier foils.

The radiant barrier foil comes either in single or double sided; breathable with ventilation holes or it may not have any ventilation; or has a foam core with some insulation value to it.  By itself, a radiant barrier has no insulation value because it reflects radiant heat from radiation, unlike insulation that slows down the transfer of heat through conduction.  Radiant barriers should also be installed along the roof trusses whenever possible compared to laying along the attic floor.

How Much Heat Comes From The Attic?

Surprisingly, not as much as you would think.  According to APS and SRP studies only 14% - 20% of your utility bill is driven by heat gain from the attic, most of it comes from windows.  I can also validate these findings from my personal experience modeling hundreds of homes in the Phoenix area under the APS energy audit program and SRP energy auditprogram.  On a side note, there is up to $1,000 in APS rebates and SRP rebates available for home energy upgrades.  Visit the APS Energy Audit Program and SRP EnergyAudit Program for more information.

If There Is No Radiant Barrier Scam, Then Why Do Most Fail?

The problem just like a driving a Prius with a hole in the gas tank - is how it is installed and a lack of understanding of what homes it will have an effect on and what homes it will do nothing for.  Most radiant barriers are sold by a sales consultant who is not a certified energy consultant and will sell radiant barriers to every home they go to and overpromise on their performance.  A comprehensive energy audit should be performed with a blower door test and by a BPI Certified auditor to test and identify the real causes and solutions to reduce energy bills and eliminate hot and cold rooms.  In an attic with R-38 insulation, the heat gain into the house is small and is approximately 80% conduction and 20% radiation.  The radiant barrier is going after that 20% of heat gain which may not be the most cost effective option.  There are certain cases where a radiant barrier would be a good choice for your home, but GreenID will not sell or install radiant barriers where it is not needed or better options exist.

Don’t freak out! What to do if a CFL light bulb breaks.

Many homeowners have been turning to APS and SRP home energy audits as an alternative to calling their local Air Conditioning Company to diagnose issues such as hot uncomfortable rooms and high energy bills.  As part of the APS and SRP energy audit program, 10 CFL light bulbs are given along with low flow aerators to start saving energy immediately. 

When CFL bulbs first came out there was some scare about absorbing the metal in our skin and the difference between the mercury vaporizing and aerosolizing.  I bet you remember the warnings to never use a vacuum cleaner, broom or pour mercury down the drain.  This is because the mercury will aerosolize in a vacuum cleaner, similar to small water droplets in the air from a hot shower, and become smaller droplets with a much bigger radius of influence than if just left as is.  If you never use a vacuum cleaner the risk of the metal aerosolizing is zero.

 Mercury vaporizing is another way for it to get in the air and potentially cause much more harm.  This risk is negated however, because the vaporization point of mercury only occurs at 674 degrees Fahrenheit!  Since it never gets that hot (even in July in Phoenix, AZ), you don’t have to worry about mercury vaporizing and inhaling the metal.  The main risk of mercury absorption is when a CFL bulb is first dropped and the metal potentially splashes up and hits us.

Here are the EPA’s cleanup instructions in case you do have a mercury spill. 

1.       Use rubber, nitrile or latex gloves

2.       Pick up broken glass with a paper towel and place both items in a labeled zip lock bag

3.    Locate visible mercury beads. Use a squeegee or cardboard to gather mercury beads. Use slow sweeping motions to keep mercury from becoming uncontrollable. Take a flashlight, hold it at a low angle close to the floor in a darkened room and look for additional glistening beads of mercury that may be sticking to the surface or in small cracked areas of the surface. Note: Mercury can move surprising distances on hard-flat surfaces, so be sure to inspect the entire room when "searching."

4.    Use the eyedropper to collect or draw up the mercury beads. Slowly and carefully squeeze mercury onto a damp paper towel. Place the paper towel in a zip lock bag and secure. Make sure to label the bag as directed by your local health or fire department.

5.    After you remove larger beads, put shaving cream on top of small paint brush and gently "dot" the affected area to pick up smaller hard-to-see beads. Alternatively, use duct tape to collect smaller hard-to-see beads. Place the paint brush or duct tape in a zip lock bag and secure. Make sure to label the bag as directed by your local health or fire department.

6.    Place all mercury beads and objects into the trash bag. Secure trash bag and label it as directed by your local health or fire department.

7.    Contact your local health department, municipal waste authority or your local fire department for proper disposal in accordance with local, state and federal laws.

8.    Remember to keep the area well ventilated to the outside (i.e., windows open and fans in exterior windows running) for at least 24 hours after your successful cleanup. Continue to keep pets and children out of cleanup area. If sickness occurs, seek medical attention immediately.

Have more questions? Contact Green ID or AZ Home Energy Audit today!

Reference: http://www.epa.gov/mercury/spills/

A visit to Hoover Dam Can Teach Lessons in Quality Building

This past Fourth of July my family made a stop at the Hoover Dam on route to Las Vegas.  The Hoover Dam is an engineering marvel on a massive scale.  For more than 70 years the damn has stood with almost no structural and decorative changes taken place.  You can still see the surveying notes along the tunnel walls and the original tiling is a work of art.  I felt like a lot more care and craftsmanship went into building the damn and all structures before the days of commodity construction.  Take old sheet metal ductwork for example, only a tin knocker had the knowledge and skill to install a home’s duct system.  These days flex duct is used and can be installed by almost anyone, which has lead to excessive conditioned air wasted to the outside and huge inefficiencies.  How long have these careless installations been doing on?  One indicator is that it is not hard to find an HVAC contractor who has been “doing this for 20 years” and has never sealed a duct system.  I’m not saying we need to go back to the days of painfully slow production and growth, but perhaps a little more common sense and a sense of pride in ones work will go a long way and have positive impacts for generations to come.

Slay your energy vampires

I have been a Phoenix energy auditor for over two years and can remember one of the first things I did when I started was to create a list of all small and large appliances and their average energy usage.  SRP and APS have an extensive list of their own for common appliances and there are several resources online and in text.   I also bought a Kill-a-watt energy monitor to find out exactly how much that coffee machine takes to run.  It turns out to be not much- but over the years I have monitored the energy consumption of a variety of appliances and gadgets I will share in these posts.

If you have a nicely landscaped backyard with a pond, you probably have a small underwater pump to keep the water filtered that may or may not have a timer.  I had a homeowner ask how much energy his pond pump was using without a timer so I hooked my energy monitor to find out.  Two hours later we got the results. 

Obviously the pond pump was small and only cost him $0.12 a day to run 24/7 however there were other factors that motivated him to put the pump on a timer.  The first being that in 1 year he had already replaced the pump two times because of failure.  With a timer, the pump will run less and extend the lifetime.  The second reason being was that his energy usage never broke more than $150 per month all year round.  Since his consumption was so low (he already had a tight, efficient home) his low hanging fruit was not so low anymore and he had to dig a little deeper to find those energy saving opportunities.  I think making the trip to the store to buy a new pump would be motivation enough for me to put it on a timer.

How to Interpret Your APS and SRP Energy Audit Report

To get a $99 APS or SRP energy audit, you can contact APS or SRP directly and they will provide 3 contractors to choose from, or you have a home energy audit done by a BPI Certified contractor of your choice.  Once the initial audit is completed, your auditor will have collected and showed you the biggest areas of waste in your home and then he or she will write up an APS or SRP approved report and software model.  This model is a specific to your home with basic information like square footage, ceiling height and window dimensions and testing data from the initial blower door and duct leakage measurements.  The software takes lots of information about your HVAC system, insulation levels and condition and shading and runs advanced heat load calculations to take your home on what we call an “efficiency test drive.” 

The best part of the software is the cost savings analysis that has been tailored to the Phoenix climate and shows the APS and SRP’s estimated cost savings for each recommendation.  That way you can make a financially based decision on whether to do a whole home retrofit.  The down side is that the report can sometimes be hard to interpret if your auditor is not walking you through it.  I’ll highlight some areas of the report that may be hard to decipher if you are not a BPI Certified energy auditor.  Although this information is specific to the APS and SRP energy audit program, the concepts can be applied to any house.

Air Leakage Results

Page 2 on APS’s Energy Audit report

Page 4 on SRP Energy Audit report

The building shell leakage is measured using the blower door and is the whole home’s leakage measured at 50 Pa.  How do you know if this is a tight home or a very leaky home?  The answer can be found by comparing that number to the Building Air Tightness Limit (aka MVR or minimum ventilation requirement) which is dependent on the size of your home, stories, climate and number of people and pets living in the home.  The MVR tells you how much ventilation is recommended for acceptable indoor air quality according to the American Society of Heating, Refrigeration and Air Conditioning Engineers (ASHRAE Standard 62.2-1989).  Under the 1989 Standard, air leakage is an acceptable method of fresh air ventilation.  This can be far from the truth though because this air leakage can come from anywhere, a dirty attic, the garage where gas appliances are located or the outside directly.  Under the new AHSRAE Standard 62.2-2007, air leakage is not an acceptable method of fresh air ventilation and mechanical ventilation is required.  In the building science world we have a saying, “build-it-tight, ventilate-it-right.”  We want to seal your home as tightly as possible then bring in fresh air in a controlled way where we know how much to bring in and we can even pre-cool it with a Recovery Ventilator.  The APS and SRP reports use the old 1989 ASHRAE Standard in their report and if you are not going to bring in controlled ventilation, you should only seal your home as tight as the MVR and no further.  There are several low-end ventilation solutions that are perform well but we’ll save that for another time.

The SRP report does not provide air leakage and insulation details on your current condition.  Your auditor should have discussed his findings with you during the audit.

Insulation

Page 3 on APS Energy Audit report

I’ve written about the importance of installing insulation correctly and how that can trump the amount of insulation you have.  If you proposal includes “air barrier” work, that is an indication of insulation misalignments and it is up to the auditor and crew to decide if the insulation needs to be moved to be aligned with the sheetrock or a new air barrier (ductboard, sheet rock, Tyvek) should be installed.

Page 4 on SRP Energy Audit report

The SRP report does not provide air leakage and insulation details on your current condition.  Your auditor should have discussed his findings with you during the audit.

Duct Leakage

Page 6 on APS Energy Audit report

The last sentence of the page reads, “Your attic duct leakage was determined to be _____.”  To get an idea if that is bad or not, take that duct leakage number and divide it by the whole home air leakage number found in the Air Leakage section (page 2 on APS’s report) to get the percentage of leakage that is being lost just in the ductwork.  Typical percentages are 10% - 20% of the conditioned air is being lost in the ductwork. 

Page 5 on SRP Energy Audit report

The SRP report does not provide the duct leakage numbers, but if you are curious your auditor will provide the number for you.  Then compare that to your total home leakage to get the percentage of air being lost through the ductwork.

Water Heaters and Combustion Appliance Testing

If you have gas appliances your energy auditor performed several combustion safety tests that test for potential safety hazards such as the flue stack or vent blocked, not enough dilution air, backdraft potential, carbon monoxide levels and gas leaks.  The report only lists carbon monoxide levels but you should be aware of what the other tests are and the potential dangers of having combustion appliances.  Carbon monoxide occurs because of incomplete combustion of gas appliances and higher levels of CO can indicate malfunctioning appliances, blocked vent, not enough makeup air for atmospheric appliances or a gas leak.

Make-up Air, Draft Pressure and Spillage

If your furnace is next to the water heater in the garage, the two probably share a common flue stack.  Often times the setup is where the furnace is power vented and the gas water heater draws dilution air passively.  This is inherently dangerous because is the flue stack is blocked and the furnace is running, carbon monoxide now has a place to escape through the gas water heater vent.  Can you say “design flaw”? 

Another potential problem that occurs more commonly in Northern Arizona but Is just as serious is when there is not enough makeup air for the gas appliance.  Today large exhaust fans and dryers draw so much air in that they can compete with an atmospherically vented appliance and potentially; backdrafting carbon monoxide down the flue stack and into the home, blow out pilot lights or cause flame roll-out.  The difference is pressure between the room with the gas appliances (CAZ or combustion appliance zone) and the outside (or inside if testing garage-into-house potential) is the driving force behind potential problems.  Having enough makeup air in the CAZ is important and it Is code to have a garage vented to the outside with 2 grilles but inside closing doors or having dryers in the same room as combustion appliances can be very dangerous.  The solution to closing interior doors is to add a pressure relief vent through a jump duct or transfer grille that allows built-up room pressure to escape. 

The auditor will test spillage, draft pressure, CO levels and room pressures under worst-case conditions to try to make the appliances fail.  These results will tell you if you have a potential problem and carbon monoxide detectors should always be installed 3 – 6 ft off the ground and functioning properly.  Your audit report should be a recommendation for fresh air ventilation through a vent fan or fresh air intake with zero annual savings.

Summary

The APS Recommended Measures table includes:

DHW is short for domestic hot water and includes solar water heating, hybrid water heaters, low flow showerheads and sink aerators (included free for APS and SRP customers), temperature turndown and tank wraps.

HVAC Upgrades is short for heating, ventilation and air conditioning and includes replacing old AC units and furnaces, duct sealing and shade screens.

Attic Insulation, Airsealing includes air barrier work and insulation upgrades.

Miscellaneous includes pool pumps.

The SRP Recommendations table lists measures out individually like pool pumps, air barrier work, duct sealing for each unit and shade screens for each side of the house.

DHW_SYS 1 Invalid can include replacing the water heater with a hybrid water heater or solar water heater.  The quantity column for insulation is in square feet.

APS Rebates for Home

APS has come out with great rebate programs and solidified their commitment to 1) energy retrofits upgrades like duct sealing and insulation, 2) renewable energy products like solar panels for electricity and hot water and finally for 3) switching out old appliances.  Each of these rebate programs are separate entities that sometimes get confused since they are always changing.  For example, APS solar rebate program has seen better days when solar electricity rebates used to be at $3.00 per watt.  Every couple of months for the last 2 years APS has dropped their solar rebates until the current amount of $1.45 per watt.  Now the best and most affordable way to get solar is through a solar lease program that significantly buys down the costs of solar panels.

APS Home Energy Audit Rebates

Now the hot program is APS’s and SRP’s Home Performance With Energy Star.  This is a national Energy Star program to make homes more healthy, comfortable and efficient.  APS and SRP adopted the program to ensure a whole-home approach to reducing energy bills while keeping homeowners safe and with better indoor air quality.  APS requires a $99 energy audit be performed on a home to diagnose the causes of high energy bills, uncomfortable rooms or excessive dust.  Once the audit is complete a report will be generated using building modeling software that gives cost savings for each upgrade.  The APS rebates will help pay up to $1,000 (or more if you have two or more AC units) off the costs of the energy retrofit.  The rebates for the Home Performance With Energy Star program are broken down below.

Duct sealing 75% off up to $250 per unit.  For most homeowners, 20% of their heating and cooling bill is wasted from duct leakage.

Air sealing 75% off up to $250.  Air sealing work can be complex as your auditor must determine

Insulation75% off up to $250

Shade screens $1 per sq ft up to $250

APS has a great visual summary of their rebate program here.

http://www.aps.com/main/rebates/residential.html?source=pgrj

http://www.energystar.gov/index.cfm?fuseaction=hpwes_profiles.showSplash

APS rebates for pool pumps

$200 for variable speed pool pump.  Each pump has to be calibrated to your pool to ensure that it is not over turning your pool.  This upgrade will reduce your bills $200 - $350 per year.  APS also provides a $75 rebate for pool timers.

APS Rebates for AC units

Air conditioning systems have become more efficient from federal standards and better technologies.  Surprisingly, APS does not overlap its duct sealing rebates with its air conditioning rebates.  With every unit we install, we include a whole home duct seal to maximize the high efficiency AC unit with a properly sealed duct system, otherwise it’s like using an umbrella with holes in it.  APS will help you pay for a higher efficiency AC unit depending on the efficiency ratings.  In the AC efficiency world there is a SEER rating, the seasonal energy efficiency ratio, EER rating, the energy efficiency ratio, and HPSF or .  In Phoenix, the EER is a more important number to pay attention to because of how hot it gets here.  The EER ratio gives a better idea of how an AC will perform under very hot conditions (100 degrees) were the SEER rating gives an idea of performance under milder conditions (89 degrees).  SRP recognizes and awards a higher rebate with higher EERs in their AC rebate program, but APS does not.

APS also has a quality installation standard similar to the post test done for the home energy audits that has to be met when installing heat pumps and furnaces in the Phoenix area also.  Only APS qualified AC companies can apply for their rebate for you, but not all of them will perform a duct testing and sealing upgrade.  These rebates and companies are separate from the solar rebates and the home energy audit rebates.  All the APS approved AC companies are required to do a sizing calculation called the Manual J calculation.  You should ask to see the results from your own home to ensure this was done.  The AC rebate program also includes a check of the refrigerant charge to make sure that the unit is properly charged to manufacture specifications and a check of the air flow.  Below is a list of the AC rebates available from APS.

SEER 13 with EER 10.8 receives $175 APS rebate

SEER 14 – 16 with EER 10.8 receives $425 APS rebate

SEER 17 with EER of 10.8 receives $525 APS rebate

All units must be installed by and APS approved AC contractor.

All contractors must perform a Manual J calculation to properly size the unit (you should verify this since it is not something a typical contractor will do).

All contractors should properly charge the unit and check airflow.

For more information on APS AC rebates, check out their link here.

http://www.aps.com/main/green/choice/choice_3.html

APS Solar Rebates

APS solar rebates are divided into solar electricity rebates and solar hot water rebates.  Solar electricity for my home was my dream growing up and has proven to be an attractive idea to thousands of homeowners across the Phoenix valley.  APS perhaps did not realize how attractive solar electricity would be since they have lowered their rebate amount dramatically since its inception.  As of May 2011, APS solar electricity rebate is at $1.45 per watt.  You can view their current budget and remaining monies available at the link below.

http://www.aps.com/main/green/choice/solar/funding.html

APS Solar Hot Water Rebates

After City and County applications have been approved, APS does random inspections of the installation.  The solar hot water system must be SRCC rated and have proof onsite.  The first 5 feet of your hot and cold water piping should be insulated to at least R-2.6.  The panels must be un-shaded during the day for the entire year.  The APS solar water heater rebates are currently at $0.50 per kWh of estimated first year savings (based on the OG-300 ratings), up to 505 off the system’s cost.  The OG-300 rating system is based on the manufacturer’s rating by the Solar Rating and Certification Corporation.  Also important to consider for solar hot water systems is the federal tax credit of 30% off the cost and Arizona state tax credit of $1,000, which makes solar hot water much more attractive.  Typical solar hot water rating systems are around 2,890 kWh per year.  An example rebate table is shown below.

Solar Hot Water Cost $5,400

APS Solar Rebate $1,445

 Arizona Tax Credit $1,000

Federal Tax Credit $1,620

Net Cost $1,335

Annual Savings $425

Simple Payback 3 years

APS Appliance and Tree Shading Rebate

APS also provides a $30 rebate to replace your old refrigerator and they will even come and pick it up for free.  Also, a understated home comfort and energy saving rebate APS offers is to plant external shading along your home to block direct sunlight.  The requirements of this rebate are that you attend a free tree shade workshop and can legally and physically plant shading trees along your home.  Visit the link below for more information.

http://www.aps.com/main/green/choice/choice_126.html

What were they thinking!?

Crawling around in attics for APS and SRP's home energy audit program has given me a pretty good idea where I can expect to find hidden “inefficiency jewels”.  I feel like a kid at Christmas discovering open wall chases, uninsulated soffit drops, misaligned insulation and unconnected ductwork. It’s like finishing a marathon, reaching the river at the Grand Canyon or reaching the Seven Falls in Tucson… well, add a little sweat, being in a 140 degree box and a chiropractor and welcome to my world of home energy audits.  Once I do find these things I often say to myself, “what were these contractors thinking!?” 

Now a home performing as a system is a relatively new concept as are the APS and SRP rebates available for helping homeowners reduce their bills and make their homes more comfortable but some of the insulating contractors, framers and developers just left their common sense at home. When insulating a home, wouldn't you want all the interior walls insulated? Or why would insulation be installed with the paper facing inside on some kneewalls and have it facing the other way of kneewalls right next to it?  I would like to share some horror stories through pictures of common and not-so-common defects in homes.  I think all good energy auditors in Phoenix will have photos and stories similar to mine, so cheers!

This is a huge source of heat gain into the home, causing hot and cold rooms and driving up energy bills each month.

APS and SRP will help pay for the cost of fixing these insulation problems.

Through the APS and SRP home energy audit program, construction defects like these will be found and fixed.

Part of the enthusiasm in finding these inefficiencies is the potential to save money on energy bills and dramatically increase the homeowner’s comfort.  Another good thing about these construction defects is that APS and SRP offer $1,000 in rebates to fix these deficiencies.

Save Energy While on Vacation or Away for the Summer

A good number of the APS and SRP home energy audits I do are for eco-conscience snowbirds.  These residents typically reside in the Phoenix, Surprise and Scottsdale areas during the winter and go back north for the summer months.  Even though homeowners are only here for part of the year, many are still motivated to have the upgrades done because of comfort and air quality problems.  Other homeowners will have efficiency upgrades like duct sealing, air sealing and insulation work done because of the APS and SRP rebate program and to drive down energy costs.  During the homeowner interview, I am always interested to find out what each homeowner does to “summarize” their home.  For Phoenix’s permanent residents, the summer is a time many will take vacation for more temperate climates.  Either way presents opportunities listed below to save energy and money while away.

Tips for “Summerizing” Your Home While on Vacation

-          Turn the water heater off completely at the breaker or shut the gas line off.  At the least, set the dial to vacation mode to minimize stand by losses.

-          Turn the thermostat up to 90 degrees.  This will keep your home cool enough to not damage the structure or your belongings.

-          Fill gallons of water and place several throughout the house to add moisture over time.

-          Unplug energy vampire’s aka electronic devices.  TV’s will use more energy in stand by mode than when turned on.  Prevent wasteful spending by simply unplugging your electronics while away.

-           Keep window shades closed and sun screens on the exterior windows to minimize heat gain during the daytime.

For more tips on “summarizing” your home while away, visit here.